Product ID:EA 911F NA SYSTEM, AS9203000
MSDS Date:03/01/1993
FSC:8040
NIIN:00-043-0822
Kit Part:Y
MSDS Number: BZSSQ

DEXTER AEROSPACE MATERIAL DIVISION

2850 WILLOW PASS ROAD
PITTSBURG, CA 94565-0031
US

Emergency Phone: 800-424-9300(CHEMTREC)

Info Phone: 510-458-8000

Preparer: MSDS DEPT

Cage: 33564

WATKINS AND ASSOCIATES INC

LILBURN, GA 30047 US

Telephone: 770-279-9200

Cage: 3D523

ZINC CHROMATE

CAS: 13530-65-9

RTECS: GB3290000

Fraction By Weight: 30-60%

OSHA PEL NONE

ACGIH TLV: 0.05 MG/M3 SKIN

POLYMER OF EPICHLOROHYDRIN, PHENOL-FORMALDEHYDE NOVOLAC

CAS: 28064-14-4

Fraction By Weight: 30-60%

GLYCEROL POLYGLYCIDYL

CAS: 25038-04-4

Fraction By Weight: 10-30%

SILICA

CAS: 112945-52-5

Fraction By Weight: 1-5%

OSHA PEL 6 MG/M3

ACGIH TLV: 6 MG/M3

VOC = <10.0 G/L ESTIMATE

RTECS: 9999999VO

Fraction By Weight: NA

OSHA PEL NOT RELEVANT

ACGIH TLV: NOT RELEVANT

LD50 LC50 Mixture:MIXTURE HAS NOT BEEN TESTED AS A WHOLE.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:BRIEF CONTACT MAY IRRIT SKIN OR CAUSE
A RASH. REPEATED OR PROLONGED SKIN CONTACT MAY RESULT IN ALLERGIC
SENSITIZATION. CARCINOGENICITY NOTE: BISPHENOL A/EPICHLOROHYDRIN
EPOXY RESIN HAS EXHIBITED MUTAG ENICITY IN BACTERIA.
Explanation of Carcinogenicity:NEITHER THIS MATERIAL NOR ANY OF IT'S
COMPONENTS IS CONSIDERED A CARCINOGEN.
Effects of Overexposure:SKIN RASH, IRRITATION.
Medical Cond Aggravated by Exposure:SKIN SENSITIZATION.

First Aid:EYE:FLUSH W/WATER FOR 15MINS. IF IRRIT PERSISTS GET MED ATTN.
SKIN:WASH THOROUGHLY W/SOAP & WATER. IF IRRIT PERSISTS GET MED
ATTN. INHAL:REMOVE VICTIM TO FRESH AIR. IF SYMPTOMS PERSIST GET MED
ATTN. I NGEST:DRINK PLENTY OF WATER. GET MED ATTN IMMED.

Flash Point:NOT TESTED
Lower Limits:NOT TESTED
Upper Limits:NOT TESTED
Extinguishing Media:DRY CHEMICAL, OR HALON FIRE EXTINGUISHER, OR WATER
SPRAY, FOAM OR FOG.
Fire Fighting Procedures:WEAR SCBA & FULL PROTECTIVE CLOTHING, SUCH AS
TURN-OUT GEAR. CARTRIDGE RESP DO NOT PROVIDE ADEQUATE PROTECTION
FOR FIREFIGHTERS OR EXOTHERM MITIGATION.
Unusual Fire/Explosion Hazard:MAY LIBERATE LARGE QUANTITIES OF DENSE
FOUL-SMELLING SMOKE WHICH MAY CONTAIN UNIDENTIFIED TOXIC GASES.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES & SAFETY
GLASSES. SCRAPE UP OR SHOVEL INTO DOT APPROVED WASTE CONTAINERS.
Neutralizing Agent:NOT APPLICABLE.

Handling and Storage Precautions:REFRIGERATED STORAGE IS RECOMMENDED TO
MAINTAIN PRODUCT QUALITY. THIS PRODUCT MAY BE STORED AT ROOM
TEMPERATURE, 77F, FOR UP TO 12 MONTHS.
Other Precautions:FOLLOW CURING SCHEDULE AS RECOMMENDED IN PRODUCT
LITERATURE.DON'T CUT/GRIND/WELD/DRILL ON/NEAR CONTAINER.AVOID
MIXING PARTS A&B IN BATCHES >1LB UNLESS PLAN TO USE IMMED.DON'T
HEAT MIXED ADHESIVE >75F UNLESS CURING SURFACES TO BE BONDED.

Respiratory Protection:UNNECESSARY WITH ADEQUATE EXHAUST VENTILATION.
Ventilation:LOCAL EXHAUST VENTILATION AT THE POINT OF USE.
Protective Gloves:BUTYL RUBBER, PVC, NITRILE RUBBER GLOVES
Eye Protection:SAFETY GLASSES W/SIDE SHIELD;CHEM GOGGLE
Other Protective Equipment:AN EYEWASH AND SAFETY SHOWER SHOULD BE
NEARBY AND READY FOR USE.
Work Hygienic Practices:WASH HANDS THOROUGHLY AFTER HANDLING MATERIALS.
Supplemental Safety and Health
FAILURE TO OBSERVE PRECAUTIONS IN MIXING/HEATING MAY RESULT IN
EXCESSIVE HEAT BUILD-UP CAUSING AN EXOTHERM. THE EXOTHERM HAS
POTENTIAL FOR RELEASE OF TOXIC GASES.

Boiling Pt:B.P. Text:UNDEFINED
Decomp Temp:Decomp Text:UNTESTED
Vapor Pres:NIL
Vapor Density:>1.0
Spec Gravity:1.67
Viscosity:*
Solubility in Water:NEGLIGIBLE
Appearance and Odor:YELLOW PASTE
Corrosion Rate:NA

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:AVOID MIXING RESIN & CURING AGENT IN
BATCHES >1 LB. UNLESS YOU PLAN TO USE IMMEDIATELY, DON'T HEAT MIXED
ADHESIVE >100F.
Hazardous Decomposition Products:CO, NOX, ALDEHYDES, ACIDS &
UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:POLYMERIZATION NOT LIKELY

Waste Disposal Methods:NOT RCRA HAZ WASTE.HOWEVER, INCINERATION IN EPA
APPROVED WASTE INCINERATOR IS PREFERRED.CHEM ADDITIONS/
PROCESSING/OTHERWISE ALTERING MATL MAY MAKE WASTE MANAGEMENT INFOR
HEREIN INCOMPLETE/INACCURATE/ INAPPROPRIATE.CONSULT STATE/LOC
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.